Introduction to CSTM
CSTM is the command mode version of STM, the utility that replaces SYSDIAG in MPE/iX Release 6.5.
I have included here a dialog illustrating how to get a memory map of a system.
This is the procedure used on MPE/iX 6.0 and earlier releases:
:sysdiag
DUI> sysmap
SYSMAP> memmapThis is the new procedure for MPE/iX 6.5 and later releases:
>:cstm
Running Command File (/usr/sbin/stm/ui/config/.stmrc).
This operation may take approximately one minute.
-- Information --
Support Tools Manager
Version A.11.00
Product Number B4708AA
(C) Copyright Hewlett Packard Co. 1995-2000All Rights Reserved
Use of this program is subject to the licensing restrictions described
in "Help-->On Version". HP shall not be liable for any damages resulting
from misuse or unauthorized use of this program.
cstm>map
Dev Last Last Op
Num Path Product Active Tool Status
=== ==================== ========================= =========== =============
1 52 NIO SCSI Interface (14)
2 52.0.0 SCSI Tape (HPC1537A)
3 52.1.0 Unknown ()
4 52.2.0 SCSI Disk (HPC2490AM)
5 52.5.0 SCSI Tape (QuantumDLT4000
6 52.8.0 Unknown ()
7 52.9.0 Unknown ()
8 56 NIO LAN/Console Interface
9 56.2 Unknown ()
10 62 CPU (282)
11 63 MEMORY (14)
cstm>select device 11
cstm>info
cstm>infolog
-- Converting a (4828) byte raw log file to text. --
Preparing the Information Tool Log for MEMORY on path 63 File ...
.... hp917 : 192.168.15.37 ....
-- Information Tool Log for MEMORY on path 63 --
Log creation time: Thu May 31 11:23:41 2001
Hardware path: 63
Basic Memory Description
Module Type: MEMORY
Total Physical Memory : 256 MB
Total Configured Memory : 256 MB
Page Size: 4096 Bytes
Memory interleaving is not supported on this machine.
Memory Board Inventory
Total Phys Configured Disabled
Board Size (MB) Total (MB) Total (MB)
------------ ---------- ---------- ----------
0A/B 64 64 0
1A/B 32 32 0
2A/B 32 32 0
3A/B 64 64 0
4A/B 64 64 0
---------- ---------- ----------
System Total: 256 256 0
Memory Controller Inventory
Hard Hardware Hardware Software Software
Physical Model Revision Model Revision Software IODC
Address Number Number Number Number Option Revision
---------- -------- -------- -------- -------- -------- --------
0xfffbf000 0x14 0 0x9 0 0 0
Bank Inventory
Log. Phys Size leave
Bank Bank Board (MB) Disabled? SPA Range (Hex) Group
---- ---- ------------ ---- --------- --------------------- -----
0 0A/B 64 enabled 0x08000000 - 0bffffff N/A
0 1A/B 16 enabled 0x0f000000 - 0fffffff N/A
1 1A/B 16 enabled 0x0c000000 - 0cffffff N/A
0 2A/B 16 enabled 0x0e000000 - 0effffff N/A
1 2A/B 16 enabled 0x0d000000 - 0dffffff N/A
0 3A/B 64 enabled 0x00000000 - 03ffffff N/A
0 4A/B 64 enabled 0x04000000 - 07ffffff N/A
Memory interleaving is not supported on this machine.
SPA - Page Map
SPA Range (Hex) Corresponding Pages
--------------------- --------------------------
0x00000000 - 03ffffff 0 - 16383
0x04000000 - 07ffffff 16384 - 32767
0x08000000 - 0bffffff 32768 - 49151
0x0c000000 - 0cffffff 49152 - 53247
0x0d000000 - 0dffffff 53248 - 57343
0x0e000000 - 0effffff 57344 - 61439
0x0f000000 - 0fffffff 61440 - 65535
Memory Error Log Summary
The memory error log is empty.
Page Deallocation Table (PDT)
This machine is not designed to have a Page Deallocation Table.
Memory Controller Rev Port
Memory controller rev port not available.
-- Information Tool Log for MEMORY on path 63 --
View - To View the file.
SaveAs - To Save the file.
Print - To Print the file.
Enter Done, Help, Print, SaveAs, or View: [Done]
cstm>† The device number corresponds to the number in the first column of the I/O map. These numbers are sequentially assigned by CSTM and have no correlation to LDEV numbers. For systems with memory extender cards plugged into multiple slots you can issue as many SELECT DEVICE commands as needed.
†† The INFO command directs CSTM to create an information log file for the selected device(s). The following command INFOLOG instructs CSTM to format the previously generated log file. It is sometimes necessary to wait a minute or so for the INFO command to complete before executing the INFOLOG command.
There is also a wealth of information available regarding disc and tape drives under CSTM using the INFO command that requires running a utility under SYSDIAG. You can see the device status, read and write error counts, and firmware revision.
cstm>select device 2
cstm>select device 4
cstm>info
cstm>infolog
-- Converting multiple raw log files to text. --
Preparing the Information Tool Log for each selected device...
.... hp917 : 192.168.15.37 ....
-- Information Tool Log for SCSI Tape on path 52.0.0 --
Log creation time: Thu May 31 12:54:11 2001
Hardware path: 52.0.0
Device Qualifier: HPC1537A
Product ID: C1537A Hardware Path: 52.0.0
Device Type: SCSI Tape Logical Unit Number: 0
Vendor: HP Product Rev Level: HP02
Firmware Revision: 3.59 Tape Load Count: 41
Correctable Errors: 0 Uncorrectable Errors: 0
Mfg Date Code: 58 Servo Revision: 14.2
Compression Status: Enabled Compression Ratio:
[instant] 1 : 1
[average] N/A
Capacity [M Byte]: 0
Drive Status: Good
=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=
-- Information Tool Log for SCSI Disk on path 52.2.0 --
Log creation time: Thu May 31 12:54:13 2001
Hardware path: 52.2.0
Product Id: C2490AM Vendor: HP
Device Type: SCSI Disk Firmware Rev: 3256
Device Qualifier: HPC2490AM Logical Unit: 0
Serial Number: 3506A07568
Capacity (M Byte): 2033.82
Block Size: 512
Max Block Address: 4165271
Data Error Log Summary
Retry Errors: 0
Correctable Errors: 0
Uncorrectable Errors: 0
Hardware Error Log Entries: